An Introduction to casing Pipes: What They Are and How They Are Used
Casing pipes are an essential component of many construction and engineering projects. They are used to line, protect, and support the walls of a borehole or tunnel, and are an integral part of the infrastructure of many industries.
casing pipe china good Factory, Oil tube Wholesale–Price high-quality good Chinese,casing pipe Chinese high-quality factory,casing pipes are typically made from steel, plastic, or concrete, and come in a variety of sizes and shapes. steel casing pipes are the most common type, and are used in a variety of applications, including Oil and gas exploration, water and sewer lines, and underground construction. Plastic casing pipes are often used in shallow wells and other applications where corrosion is not a concern. Concrete casing pipes are used in deep wells and other applications where corrosion is a concern.
| Chemical composition, Mass Fraction (%) | ||||||||||||||
| grade | C | Mn | Mo | Cr | Ni | Cu | P | S | Si | |||||
| Type | min | max | min | max | min | max | min | max | max | max | max | max | max | |
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
| H40 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
| J55 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
| K55 | — | — | — | — | — | — | — | — | — | — | — | — | 0.03 | — |
| N80 | 1 | — | — | — | — | — | — | — | — | — | — | 0.03 | 0.03 | — |
| N80 | Q | — | — | — | — | — | — | — | — | — | — | 0.03 | 0.03 | — |
| R95 | — | — | 0.45 c | — | 1.9 | — | — | — | — | — | — | 0.03 | 0.03 | 0.45 |
| L80 | 1 | — | 0.43 a | — | 1.9 | — | — | — | — | 0.25 | 0.35 | 0.03 | 0.03 | 0.45 |
| L80 | 9Cr | — | 0.15 | 0.3 | 0.6 | 0.9 | 1.1 | 8 | 10 | 0.5 | 0.25 | 0.02 | 0.03 | 1 |
| L80 | 13Cr | 0.15 | 0.22 | 0.25 | 1 | — | — | 12 | 14 | 0.5 | 0.25 | 0.02 | 0.03 | 1 |
| C90 | 1 | — | 0.35 | — | 1.2 | 0.25 b | 0.85 | — | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
| T95 | 1 | — | 0.35 | — | 1.2 | 0.25 b | 0.85 | 0.4 | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
| C110 | — | — | 0.35 | — | 1.2 | 0.25 | 1 | 0.4 | 1.5 | 0.99 | — | 0.02 | 0.03 | — |
| P110 | e | — | — | — | — | — | — | — | — | — | — | 0.030 e | 0.030 e | — |
| Q125 | 1 | — | 0.35 | 1.35 | — | 0.85 | — | 1.5 | 0.99 | — | 0.02 | 0.01 | — | |
| NOTE Elements shown shall be reported in product analysis. | ||||||||||||||
| a The carbon content for L80 may be increased up to 0.50 % maximum if the product is oil-quenched or polymer-quenched. | ||||||||||||||
| b The molybdenum content for Grade C90 Type 1 has no minimum tolerance if the Wall thickness is less than 17.78 mm. | ||||||||||||||
| c The carbon content for R95 may be increased up to 0.55 % maximum if the product is oil-quenched. | ||||||||||||||
| d The molybdenum content for T95 Type 1 may be decreased to 0.15 % minimum if the wall thickness is less than 17.78 mm. | ||||||||||||||
| e For EW Grade P110, the phosphorus content shall be 0.020 % maximum and the sulfur content 0.010 % maximum. | ||||||||||||||
Casing pipes are installed in a borehole or tunnel by a process known as “casing running”. This involves lowering the casing pipe into the borehole or tunnel, and then securing it in place with a variety of methods, such as grouting, welding, or bolting. Once the casing pipe is in place, it is then Sealed with a variety of materials, such as cement, grout, or rubber.
Casing pipes are an essential part of many construction and engineering projects, and are used to protect and support the walls of a borehole or tunnel. They come in a variety of sizes and shapes, and are typically made from steel, plastic, or concrete. Casing pipes are installed in a borehole or tunnel by a process known as “casing running”, and are then sealed with a variety of materials.
| Calculated Mass c | |||||||||||
| Nominal Linear Mass T& C b,c | Wall Thick- ness | em, Mass Gain or Loss Due to End Finishing d | |||||||||
| Labels a | Outside Diameter | Inside Diameter | Drift Diameter | Plain- end | kg | ||||||
| Round Thread | Buttress Thread | ||||||||||
| wpe | |||||||||||
| D | kg/m | t | D | mm | kg/m | Short | Long | RC | SCC | ||
| mm | mm | mm | |||||||||
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 |
| 7 | 17 | 177.8 | 25.6 | 5.87 | 166.06 | 162.88 | 24.89 | 7.61 | — | — | — |
| 7 | 20 | 177.8 | 29.91 | 6.91 | 163.98 | 160.8 | 29.12 | 6.74 | — 7.94 | — 8.28 | — 0.58 |
| 7 | 23 | 177.8 | 34.67 | 8.05 | 161.7 | 158.75 e 158.52 156.24 153.90 | 33.7 | 6.26 | 7.94 | 8.28 | 0.58 |
| 7 | 23 | 177.8 | 34.67 | 8.05 | 161.7 | 152.40 e | 33.7 | 6.26 | 7.37 | 7.65 | –0.54 |
| 7 | 26 | 177.8 | 39.14 | 9.19 | 159.42 | 151.6 | 38.21 | 5.79 | 6.79 | 7.13 | –0.69 |
| 7 | 29 | 177.8 | 43.6 | 10.36 | 157.08 | 149.32 | 42.78 | — | 6.23 | 6.4 | –1.31 |
| 7 | 32 | 177.8 | 47.92 | 11.51 | 154.78 | 147.18 | 47.2 | — | 6.23 | 6.4 | –1.31 |
| 7 | 32 | 177.8 | 47.92 | 11.51 | 154.78 | 142.86 | 47.2 | — | 5.68 | 5.79 | –1.91 |
| 7 | 35 | 177.8 | 52.09 | 12.65 | 152.5 | 139.72 | 51.52 | — | 5.18 | 5.24 | –2.47 |
| 7 | 38 | 177.8 | 56.1 | 13.72 | 150.36 | 136.52 | 55.52 | — | — | — | — |
| 7 | 42.7 | 177.8 | 63.84 | 15.88 | 146.04 | 133.38 | 63.41 | — | — | — | — |
| 7 | 46.4 | 177.8 | 69.35 | 17.45 | 142.9 | 130.18 | 69.01 | — | — | — | — |
| 7 | 50.1 | 177.8 | 74.85 | 19.05 | 139.7 | 74.58 | — | — | — | — | |
| 7 | 53.6 | 177.8 | 80.21 | 20.62 | 136.56 | 79.93 | — | — | — | — | |
| 7 | 57.1 | 177.8 | 85.42 | 22.22 | 133.36 | 85.25 | — | ||||
| 7 5/8 | 24 | 193.68 | 35.72 | 7.62 | 178.44 | 175.26 | 34.96 | 7.11 | — 8.58 | — 9.12 | — 2.59 |
| 7 5/8 | 26.4 | 193.68 | 39.29 | 8.33 | 177.02 | 173.84 | 38.08 | 6.78 | 7.91 | 8.38 | 1.84 |
| 7 5/8 | 29.7 | 193.68 | 44.2 | 9.52 | 174.64 | 171.46 | 43.24 | — | 7.13 | 7.51 | 0.98 |
| 7 5/8 | 33.7 | 193.68 | 50.15 | 10.92 | 171.84 | 168.66 | 49.22 | — | 6.16 | 6.44 | – 0.10 |
| 7 5/8 | 39 | 193.68 | 58.04 | 12.7 | 168.28 | 165.1 | 56.68 | — | 5.32 | 5.5 | –1.03 |
| 7 5/8 | 42.8 | 193.68 | 63.69 | 14.27 | 165.14 | 161.96 | 63.14 | — | 4.87 | 5.01 | –1.52 |
| 7 5/8 | 45.3 | 193.68 | 67.41 | 15.11 | 163.46 | 160.28 | 66.54 | — | 4.48 | 4.57 | –1.96 |
| 7 5/8 | 47.1 | 193.68 | 70.09 | 15.88 | 161.92 | 158.74 | 69.63 | — | — | — | — |
| 7 5/8 | 51.2 | 193.68 | 76.19 | 17.45 | 158.78 | 155.6 | 75.84 | — | — | — | — |
| 7 5/8 | 55.3 | 193.68 | 82.3 | 19.05 | 155.58 | 152.4 | 82.04 | — | |||
| 7 3/4 | 46.1 | 196.85 | 68.6 | 15.11 | 166.63 | 165.10 e | 67.72 | — | — | — | — |
| 7 3/4 | 46.1 | 196.85 | 68.6 | 15.11 | 166.63 | 163.45 | 67.72 | — | — | — | — |
